SciELO - Scientific Electronic Library Online

 
vol.84 issue200Study of the dispersion of Cloisite 10A in recycled polyethylene terephtalate by extrusionEvaluation of the stability of a highway slope through numerical modeling author indexsubject indexarticles search
Home Pagealphabetic serial listing  

Services on Demand

Journal

Article

Indicators

Related links

  • On index processCited by Google
  • Have no similar articlesSimilars in SciELO
  • On index processSimilars in Google

Share


DYNA

Print version ISSN 0012-7353

Dyna rev.fac.nac.minas vol.84 no.200 Medellín Jan./Mar. 2017

https://doi.org/10.15446/dyna.v84n200.52903 

Articles

Simulation model to estimate bending overstrength in concrete elements

Modelo de simulación para estimar la sobrerresistencia a flexión de elementos de concreto

Alejandro Hernández-Martíneza 

Adrián David García-Sotoa 

Jesús Gerardo Valdés-Vázqueza 

a Departamento de Ingeniería Civil de la División de Ingenierías, Universidad de Guanajuato, Guanajuato, México. alejandro.hernandez@ugto.mx, adgarcia@ugto.mx, valdes@ugto.mx


Abstract

A simulation model to estimate bending overstrength in reinforced concrete elements is presented. The simulation model employs basic design hypotheses according to NTC-04 [1] and ACI 318-11 [2] for rectangular concrete beams subjected to bending with rebars in the tension zone only. Concrete compression strength is included in the model as a random variable to estimate the uncertainty in bending strength on rectangular beams. Concrete compressive strength is evaluated for more than 16,000 compression tests for mixtures designed for 200 kgf/cm² (19.6 MPa) and 250 kgf/cm² (24.5 MPa). The main objective of this work is to assess the influence of real concrete compressive strength on the bending overstrength computed from analytical models used by actual construction codes like NTC-04 and ACI 318-11.

Keywords: simulation model; bending overstrength; concrete compressive strength; random variable

Resumen

En este artículo se presenta un modelo de simulación para estimar la resistencia a flexión de elementos de concreto. El modelo de simulación emplea las hipótesis básicas de diseño de acuerdo con las NTC-04 [1], así como con el ACI 318-11 [2] para vigas de sección rectangular con acero de refuerzo solamente en la zona de tensión. La resistencia a la compresión del concreto se integra al modelo como una variable aleatoria con el fin de estimar la incertidumbre en la resistencia a flexión de las vigas. La resistencia a la compresión del concreto se estima a partir de más de 16 mil pruebas con mezclas diseñadas para obtener 200 kg/cm² (19.6 MPa) y 250 kg/cm² (24.5 MPa). El principal objetivo de este trabajo es el de evaluar la influencia que tiene la resistencia a la compresión del concreto en la sobrerresistencia estimada a flexión empleando modelos analíticos que se encuentran en los reglamentos de diseño como lo son las NTC-04 y el ACI 318-11.

Palabras clave :  modelo de simulación; resistencia a flexión; resistencia a compresión del concreto; variable aleatoria

1. Introduction

Reinforced concrete is a composite material created by the mixture of cement, stone aggregates, water, and steel reinforcement. This construction material is used in a wide range of applications for building structures of any kind due to its versatility and relatively low cost. Without reinforcement, building modern concrete structures would not be possible, since concrete has a high compression strength but also a low tensile strength. Steel reinforcement bars are added to support tensile stress that concrete cannot resist.

Reinforced concrete has been studied mostly through laboratory experiments due to its complex behavior. Several experiments and analytical studies have been carried out by Kent and Park [3]; Mander et al. [4]; Song and Lu [5]; Yi et al. [6] among many others. These studies have shown that the presence of transverse reinforcement confines the concrete core and improves concrete performance, making a more ductile structural element and increasing the compressive strength as shown in Fig. 1.

Beams are structural elements that mainly resist bending and shear forces. There are many studies to estimate bending behavior including shear interaction such as the ones conducted by Vecchio & Collins [8,9], Ichinose [10], Priestley & Calvi [11], Priestley et al. [12], Hamutçuoğlu & Scott [13], Xu and Zhang [14], etc.

On the other hand, large research efforts have been devoted to estimating the seismic vulnerability of irregular structures with respect to torsionally balanced buildings, some of them are summarized by De-Stefano & Pintucchi [15]. More recently, mass, stiffness, and strength discontinuities have been investigated separately to obtain a clear estimate of their effects on the structural behavior, like those performed by Valmundsson & Nau [16], Chintanapakdee & Chopra [17], De-Stefano et al. [18], Guner & Vecchio [19,20], Reyes & Chopra [21,22], Magliulo et al. [23] among many others. The abovementioned studies have reported that among mass, stiffness, and strength irregularities, the latter lead to larger increments in plastic demands compared with regular structures. Nevertheless, in most works, overstrength is evaluated as the ratio of available strength to estimated demand, without taking into account the variability of material properties, using only the nominal values of material properties to compute the available strength. Therefore, the assessment of the actual overstrength in a structural element is an important issue because if the overstrength is highly dispersed it may lead to unexpected ductility demands.

Concrete structural elements subjected to bending are designed in accordance with building code requirements without considering confinement effects or shear interactions. NTC-04 [1] and ACI 318-11 [2] building codes, which are commonly used in Mexico, use basically the same simplifying assumptions to determine the bending strength of reinforced concrete elements, which are:

  • The distribution of strains on the cross section are linear

  • Stress distribution in the concrete compression zone is known, and can be computed by an equivalent rectangular stress block

  • There are no relative shifts among steel reinforcement and the surrounding concrete.

  • The structural element reaches its bending strength at an ultimate concrete strain ε cu = 0.003

  • Steel reinforcement has an elastic-plastic behavior

Fig. 2 summarizes some simplifying key hypotheses established by NTC-04 code for rectangular sections. Computing force equilibrium conditions, the nominal bending strength can be obtained from eq. (1).

Source: Adapted from [7].

Figure 1 Load-strain relationships for concrete square prisms with different transverse reinforcement. 

Source: Adapted from [24].

Figure 2 NTC-04 hypotheses to compute bending strength 

Source: Adapted from [24].

Figure 3 ACI 318-11 hypotheses to compute bending strength 

(1)

where:

Eq. (1) b denotes the beam width, 𝑑 the distance from the reinforcement centroid to the extreme compression fiber, A s is the steel reinforcement area, ƒ v is the steel yielding stress, and ƒ c is the stress magnitude on the equivalent stress block, as shown in Fig. 2.

Analogously, Fig. 3 shows some basic hypotheses used by the ACI 318-11 code for rectangular sections, and considering force equilibrium conditions, the nominal moment strength can be estimated from Eq. (2).

(2)

where:

Eqs. (1) and (2) are only valid when steel reinforcement yields, which may lead to ductile failure. According to NTC-04, steel yields without brittle failure providing a steel ratio 𝜌 between the limits . The NTC-04 defines the minimum steel ratio with Eq. (3), and the maximum steel ratio as 0.9 for elements that do not resist seismic forces and 0.75 for elements that resist seismic forces.

(3)

The balanced steel ratio 𝜌 𝑏 corresponds to the case when concrete and steel reinforcement reach their ultimate strain ε cu 0.003 and yield stress (ƒ s = ƒ v ) at the same time respectively. In NTC-04, the balanced steel ratio is evaluated from Eq. (4).

(4)

where β is a factor that adjusts the depth of the equivalent stress block respect to ƒ c * that represents the “effective” concrete compressive strength, which are calculated according to the equations shown in Fig. 2.

Analogously, the ACI 318-11 code defines a minimum steel ratio according to Eq. (5), and to ensure that not too much steel reinforcement is provided, steel strain ε s shall not be less than 0.004. This limit corresponds to a slightly lower steel ratio specified in the NTC-04 code.

(5)

The principal difference between both codes is the geometry of the equivalent stress compression block (see Figs. 2 y 3). Thus, while the NTC-04 concrete block stress is computed on the basis of , the ACI 318-11 it is calculated as 0.85 ƒc’. The reason for this difference is the use of an “effective” concrete strength by the NTC-04 to account some possible deficiencies in concrete production.

The structural design process involves the assumption that material strengths are known (ƒ c for concrete and ƒ v for reinforcement steel), however in real world material properties are not unique and invariant, as can be seen in Fig. 4, where concrete compressive strength for two design nominal values are plotted in histograms. The variability of material properties can significantly influence the expected strength of the structural element. To evaluate overstrength in reinforced concrete elements subjected to bending, a simulation model is proposed following the recommendations made by Kim & Nelson [25], Law [26,27], and Ingals [29] to develop an adequate simulation model.

As previously mentioned, the bending strength of reinforced concrete elements, considering the variability of concrete compressive strength for local conditions of quality control, is evaluated in this paper. To do this, the concrete compressive strength is considered as a random variable, which data (observed) samples are described in the following section.

Note that the term overstrength is used because it is generally expected that the actual bending strength is greater than the calculated nominal strength. However, the compressive strength is uncertain and not necessarily larger than the nominal value, and may even be smaller.

Estimating the bending overstrength is an important issue because its evaluation allows us to predict probabilistically the actual bending strength in a structural element, and also to know the overstrength distribution related to the considered compressive strength and the used design model. Additionally, it will improve the nonlinear models to predict undesirable behavior under extreme load cases, such as load conditions that involves earthquake solicitations.

Therefore, the main objective of this study is to assess the influence of real concrete compressive strength on the bending strength of reinforced concrete beams by using a simulation model considering the NTC-04 and ACI 318-11 requirements.

2. Concrete compressive strength data and fitting

More than 16,000 concrete compressive strength tests are carried out by Contratos y Servicios Maquipa SA de CV, located at the city of Aguascalientes, Ags., Mexico, for concrete specimens sampled from mixed concrete provided by local suppliers. All tests correspond to specimens of concrete designed for a nominal compression strength of 200 kgf/cm² (19.6 MPa) and 250 kgf/cm² (24.5 MPa) at 28 days age. Fig. 4 shows the histograms corresponding to each concrete compressive strength.

Assuming that concrete compressive strength is an independent identically distributed (IID) random variable, all data tests are fitted to several probability distribution functions to represent data as recommended by Law [26]. Chi-square and Kolmogorov-Smirnov goodness of fit tests are computed to determine the best probability function that represents data. The best fit resulted when the logistic distribution is considered, , for both nominal design concrete compressive strengths. The fitted distributions are shown with a thick line in Fig. 4 using parameter values presented in Table 1 for each case. For more information on this probability distribution, and others considered in the present paper, the interested reader is referred to the Appendix.

Source: The authors

Figure 4 Concrete compressive strength histograms at 28-days age 

Table 1 Parameter values to represent data with Logistic function 

Source: The authors

3. Simulation Model

Considering concrete compressive strength as an IID random variable, i.e., , the normalized bending strength Φ can be estimated for each code from Eqs. (6) and (7) which are described in the following.

(6)

(7)

In Eqs. (6) and (7) resistance reduction factors are added (F R and Φ) as specified on the considered construction codes. These reduction factors have an invariant value of 0.9 for both codes. Reduction factors are used to include the uncertainties associated to the resistance and the employed hypotheses in design, as well as to provide a certain level of safety. In Eqs. (6) and (7), reduction factors are considered random variables with Uniform distributions as an indirect way to account for the modeling error, which is reflected when the difference between the models to compute the resistance compared to the experimental results are significant ), and when these same models generate an excellent bending strength estimation ( 𝐹 𝑅 = 𝜙 = 1.0), and also the intermediate cases. The use of the Uniform distribution implies that not enough information on the uncertainty of the considered variable is available (Benjamin and Cornell, 1970) [27], as in this case, at least for the Mexican practice. Thus, reduction factor can be estimated by Eq. (8).

(8)

As shown in Figs. 1 and 2, C represents the neutral axis depth that establishes the force equilibrium among concrete compression C and steel tension 𝑇. Eqs. (1) and (2) are only valid when steel reinforcement yields, i.e., ƒ s = ƒ y , where ƒ s denotes the stress on steel. As there is the possibility that this condition does not occur, i.e., ƒ s < ƒ y ,, 𝑐 is computed by employing a numerical approach based on the secant method to ensure that force equilibrium is reached. For this reason, it is necessary to define transverse section dimensions to perform the numerical calculation process. Consequently, common values of b and d are selected using Eqs. (9) and (10).

(9)

(10)

Note that the selection of b and d as Uniform random variables is not intended to account for the uncertainty in the geometric properties, but simply to generate beams with a wide variety of sections to avoid any effect of the aspect ratio in the results. Obviously, different sections lead to different bending strengths, but the conclusions hold for concrete beams in general, since Eqs. (6) and (7) are normalized (note that 𝑏 and 𝑑 appear both in the numerator and denominator). In fact, these equations can be considered as the ratio of the actual bending strength to nominal bending strength when considering the probabilistic analysis and described assumptions. As shown, Eqs. (6) and (7) are normalized because the denominators determine the bending strength in accordance with each construction code, while the numerators include compressive strength as a random variable. The way in which the numerators are expressed permit the use of the numerical procedure to compute the force equilibrium in function of the neutral axis 𝑐 as already mentioned.

The procedure to compute Φ is as follows:

  1. Define section properties

  2. Estimate d from eq. (9)

  3. Estimate 𝑏 from eq. (10)

  4. Estimate concrete compressive strength

  5. Compute neutral axis depth 𝑐 to ensure force equilibrium

  6. Estimate reduction factor from Eq. (8)

  7. Apply Eqa. (6) or (7) considering

4. Results

The outlined simulation model is used, and results of Φ for 20 million of simulations are shown as histograms in Fig. 5, considering the minimum steel ratio ρ as stipulated in Eq. (5) for ƒc*= 250 kgf/cm² (24.5 MPa) and both building codes. As may be observed, in almost all cases the bending strength is greater than the value calculated with the nominal material properties. Similar results are obtained for ƒc’= 200 kgf/cm² (19.6 MPa). Table 2 shows central tendencies and dispersion values for both cases, where Φmin, Φmax, Φmed, and Φmod denote the corresponding minimum, maximum, median and mode for each case. Results in Table 2 show that the average value bending overstrength Φ 𝑚𝑒𝑑 is around 6% greater than the design value in all cases, and that at most 0.4% and 1.4% of the simulated data have bending stress under the nominal value for NTC-04 and ACI 318-11, respectively.

Source: The Authors.

Figure 5 Histograms of Φ for 𝜌= 𝜌 𝑚𝑖𝑛 and ƒ c =250 kgf/cm² (24.5 MPa) 

Table 2 Central tendencies and dispersion values for  

Source: The authors.

For the same simulation scheme, Fig. 6 shows the histograms of Φ, but in this case for steel ratio and ƒ c = 250 kgf/cm² (24.5 MPa). An increment of Φ values can be observed respect to the previous results. Similar trends occur for ƒ c = 200 kgf/cm² (19.6 MPa) as can also be observed in Table 3. An average value of bending strength around 11% and 6% greater than the nominal is obtained for NTC-04 and ACI 318-11, respectively. However, a greater number of values fall under the nominal bending strength, being about 1.5% of the cases for NTC-04 and 7% for ACI 318-11, respectively.

Source: The Authors.

Figure 6 Histograms of Φ for and ƒ c =250 kgf/cm² (24.5 MPa) 

Table 3 Central tendencies and dispersion values for  

Source: The authors.

Designing all structural elements with the same steel ratio hardly can occur in professional practice, so it is more reasonable to consider a wide range of possibilities within the limits stipulated in the constructions codes. Therefore, in Fig. 7 histograms of Φ considering the steel ratio as an IID random variable with Uniform distribution according to eq. (11) and ƒ c = 250 kgf/cm² (19.6 MPa) are shown. The results for ƒ c = 200 kgf/cm² (24.5 MPa) have a similar distribution that are shown in Fig. 7b. The central tendencies and dispersion values for these results are shown in Table 4.

(11)

Source: The authors.

Figure 7 Histograms of Φ for and ƒc’=250 kgf/cm² (24.5 MPa) 

Table 4 Central tendencies and dispersion values for  

Source: The authors.

In general, it is desirable to provide a steel ratio not close to the minimum or maximum allowable values, since these limits are associated with brittle failure. Thus an intermediate steel ratio is preferred. Consequently, Fig. 8 shows the values of Φ when steel ratio is estimated as an IID random variable with Triangular distribution according to eq. (12).

(12)

Source: The authors.

Figure 8 Histograms of Φ for and ƒc’=250 kgf/cm² (24.5 MPa) 

Table 5 Central tendencies and dispersion values for  

Source: The authors.

Form results shown in Figs. 7-8, as well as central tendencies values and dispersion showed in Tables 4 and 5, it may be established that the distribution of steel ratio has no significant influence on the obtained values of Φ since the obtained results are almost equal for both cases. Therefore, similar results are expected if any other distribution for the steel ratio is considered. From Table 5, it can be seen that the maximum bending overstrengths, Φ max , that can be obtained are 25% higher than the nominal value for NTC-04 and 20% for ACI 318-11. The average overstrength Φ med ranges from 9% to 14% greater than the nominal value for NTC-04, and approximately 6% for ACI 318-11. The number of cases with bending strength lower than the nominal value are at most 1% for NTC-04, while they are about 4% for the ACI 318-11.

It is important to note that all results presented herein are based on probability functions of concrete compressive strength (see Fig. 4) where 27% and 35 % (for ƒ c of 200 kgf/cm² and 250 kgf/cm², respectively) of concrete compressive strength are lower than the design value.

5. Conclusions

In this paper, bending overstrength estimation for rectangular simply reinforced beams using a numerical simulation model is presented. Bending strength is estimated using the design hypotheses and requirements according to NTC-04 [1] and ACI 318-11 [2] construction codes.

Samples of concrete compression strength for ƒ c of 200 kgf/cm² and 250 kgf/cm² provided in this study are used to carry out fitting distribution, and result in the use of the logistic distribution as an adequate probabilistic characterization of the data for both cases. When a lower bound of the steel ratio is considered (Fig. 5 and Table 2), the bending overstrength is, on average, approximately 6% greater than that obtained with a deterministic approach, achieving up to 14% of overstrength as maximum. A few bending strength values are lower than those computed with the nominal values, resulting in around 0.3 % of the cases for NTC-04 and 1.4% for ACI 318-11.

On the other hand, when an upper bound of the steel ratio is provided (Fig. 6 and Table 3), greater overstrength values can be obtained. The mean bending overstrength is around 11% greater than the design value for NTC-04 and 6% for ACI 318-11, reaching up to 26% and 20% as maximum overstrength, respectively. Also, more cases of bending strength values under the nominal strength occur, resulting in around 5% of the cases for NTC-04 and 7% for ACI 318-11. In other words, higher overstrength dispersion is found for this case respect to previous results.

To take into consideration that structural elements can be designed with different steel ratios in the same structure, this parameter is added to the simulation model as a random variable. Two distribution functions are used to represent the steel ratio. Initially a Uniform distribution is used to represent the equal probability of occurrence in the range considered defined by Eq. (11). Obtained results are shown in Fig. 7, and are summarized in Table 4. Also, a Triangular distribution is used to represent a probability steel ratio according to Eq. (12) to represent a greater probability of using an average steel ratio with respect to minimum and maximum limits. Results using a Triangular distribution are shown in Fig. 8 as well as in Table 5. As may be observed, results using both probability functions are quite similar. This behavior implies that a particular selected probability function for the steel ratio may have no significant influence on the obtained results. In the mentioned cases (for Uniform and Triangular distributions), the average overstrength Φ med is around 8% to 14% larger than the nominal value for NTC-04 and near to 6% larger for ACI 318-11, achieving maximum values of overstrength of about 25% and 20%, respectively. Bending strength values under the nominal values are less than 1% of the cases for NTC-04 and 4.5 % for ACI 318-11.

Obtaining larger bending strengths with respect to deterministic values computed as per NTC-04 does not mean that the assumptions considered by this building code are better than those for ACI 318-11. This simply occurs because the NTC-04 code employs an “effective” concrete compression strength ƒ c * = 0.8 𝑓 𝑐 ′ , i.e., NTC-04 considers that the real concrete compressive strength may be up to 20% less than the nominal, thus a larger bending strength for the same material properties is an expected consequence in the presented results. Additionally, it should be considered that the design forces computed for each design code may correspond to different load combinations with different load factors; therefore, care must be taken for direct quantitative comparisons.

Note that, if desired, the results in Fig. 7 (or 8) can be employed in studies where a probability analysis accounting for bending overstrength of reinforced concrete elements was of interest.

The results of this study suggest that, on average, the bending strength is larger than that obtained with invariant design concrete compressive strength (nominal). Since the results can be greatly dependent on the actual steel reinforcement yield strength, inclusion of the yield strength as a random variable in the simulation model, and is desirable for future works. Also, the confinement effect and shear interaction could be included to evaluate their influence on bending overstrength.

Since resistance variation has a significant influence on the behavior of structures subjected to seismic demands, to incorporate this variability into numerical structural models will lead to a more adequate prediction of ductility demands. Additionally, an adequate overstrength estimation will also contribute to propose better structural reliability models and therefore a better assessment of the structural safety.

Acknowledgments

The support of the Universidad de Guanajuato to develop the present paper, and the support of Contratos y Servicios Maquipa SA de CV, for generously providing the tests information, are gratefully acknowledged.

References

[1] Gobierno del Distrito Federal GDF. Normas técnicas complementarias para diseño y construcción de estructuras de concreto. México City: Gaceta Oficial del Distrito Federal, 2004. [ Links ]

[2] American Concrete Institute ACI. Building code requirements for structural concrete (ACI 318-11) and commentary. Farmington Hills, MI, USA, 2011. [ Links ]

[3] Kent, D.C and Park R., Flexural members with confined concrete. Journal of Structural Division ASCE, 97(7), pp 1969-1990, 1971. [ Links ]

[4] Mander, J.B., Priestley, M.J.N, and Park R., Theoretical stress-strain model for confined concrete. Journal of Structural Engineering ASCE, 114(8), pp 1804-1826, 1988. [ Links ]

[5] Song, Z.H. and Lu, Y., Numerical simulation of concrete confined by transverse reinforcement. Computers and Concrete, 8(1), pp. 23-41. 2011. [ Links ]

[6] Yi, W.J., Li, P. and Kunnath, S.K., Experimental studies on confinement effect of steel hoops in concrete columns. ACI Structural Journal, 109(1), pp. 3-10, 2012. [ Links ]

[7] Park, R. and Paulay, T., Reinforced concrete structures. John Wiley & Sons, 1975. [ Links ]

[8] Vecchio, F.J. and Collins, M.P., The modified compression-field theory for reinforced concrete elements subjected to shear. ACI Journal, 83(22), pp. 219-231, 1986. [ Links ]

[9] Vecchio, F.J. and Collins, M.P., Predicting the response of reinforced concrete beams subjected to shear using compression field theory. ACI Structural Journal, 85(S27), pp. 258-268, 1988. [ Links ]

[10] Ichinose, T., A shear design equation for ductile R/C members. Journal of Structural Division ASCE, 97(7), pp. 1969-1990, 1992. [ Links ]

[11] Priestley, M.J.N and Calvi, G.M., Towards a capacity-design assessment procedure for reinforced concrete frames. Earthquake Spectra, 7(3), pp 413-437, 1991. [ Links ]

[12] Priestley, M.J.N., Verma, R. and Xiao, Y., Seismic shear strength of reinforced concrete columns. Journal of Structural Engineering, 120(8), pp. 2310-2329, 1994. [ Links ]

[13] Hamutçuoğlu, O.M. and Scott, M.H., Finite element reliability analysis of bridge girders considering moment-shear interaction. Structural Safety, 31(5), pp. 356-362, 2009. [ Links ]

[14] Xu, W.J. and Zhang, J., Hysteretic shear-flexure interaction model of reinforced concrete columns for seismic response assessment of bridges. Earthquake Engineering & Structural Dynamics, 40(3), pp. 258-268, 1988. [ Links ]

[15] De-Stefano, M. and Pintucchi, B., A review of research on seismic behavior of irregular building structures since 2002. Bulletin of Earthquake Engineering, 6(2), pp. 285-308, 2008. [ Links ]

[16] Valmundsson, E.V. and Nau, J.M., Seismic response of buildings frames with vertical structural irregularities. Journal of Structural Engineering, 123(1), pp 30-40, 1997. [ Links ]

[17] Chintanapakdee, C. and Chopra, A.K., Evaluation of the modal pushover analysis using generic frames. Earthquake Engineering & Structural Dynamics, 32(3), pp 417-44, 2003. [ Links ]

[18] De-Stefano, M., Marino, E.M. and Rossi, P.P., Effect of overstrength on the seismic behavior of multi-storey regularly asymmetric buildings. Bulletin of Earthquake Engineering, 4(1), pp 23-42, 2006. [ Links ]

[19] Guner, S. and Vecchio, F.J., Pushover analysis of shear-critical frames: Formulation. ACI Structural Journal, 107(1), pp. 63-72, 2010. [ Links ]

[20] Guner, S. and Vecchio, F.J., Pushover analysis of shear-critical frames: Verification and Application. ACI Structural Journal, 107(1),pp. 72-81, 2010. [ Links ]

[21] Reyes, J.C., and Chopra, A.K., Three-dimensional modal pushover analysis of buildings subjected to two components of ground motion, including it evaluation for tall buildings. Earthquake Engineering & Structural Dynamics, 40(7), pp. 789-806, 2011. [ Links ]

[22] Reyes, J.C. and Chopra, A.K., Evaluation of three-dimensional modal pushover analysis for unsymmetric-plan buildings subjected to two components of ground motion. Earthquake Engineering & Structural Dynamics, 40(13), pp. 1473-1494, 2011. [ Links ]

[23] Magliulo, G. Capozzi, V. and Ramasco, R., Seismic performance of R/C frames with overstrength discontinuities in elevation. Bulletin of Earthquake Engineering, 10(2), pp. 679-694, 2012. [ Links ]

[24] González-Cuevas, O.M. and Robles-Fernández, F., Aspectos Fundamentales del Concreto Reforzado 4th Ed. LIMUSA, 2009. [ Links ]

[25] Kim, S.H. and Nelson, B.L., Selectin the best system: Theory and methods. Proceedings of the 2003 Winter Simulation Conference, Boulder, CO, USA, 2003. [ Links ]

[26] Law, A.M., Simulation Modeling and Analysis 4th Ed. McGraw-Hill, 2007. [ Links ]

[27] Benjamin, J.R. and Cornell, C.A., Probability statistics and decisions for civil engineers. McGraw-Hill Book Company, New York, 1970. [ Links ]

[28] Law, A.M., How to build a valid credible simulation models. Proceedings of the 2009 Winter Simulation Conference, Austin TX, USA, 2009. [ Links ]

[29] Ingals, R.G., Introduction to simulation. Proceedings of the 2008 Winter Simulation Conference, Miami FL, USA, 2009. [ Links ]

1How to cite: Hernández-Martínez, A., García-Soto, A. D. & Valdés-Vázquez, J. G. Simulation model to estimate bending overstrength in concrete elements DYNA 84 (200) 112-120, 2017.

Appendix

This appendix shows the mathematical expression for each probability function used in this paper considering 𝑋 as a random variable

Density

Distribution

Density

Distribution

Density

Distribution

Received: September 03, 2015; Revised: March 20, 2016; Accepted: September 16, 2016

Creative Commons License This is an open-access article distributed under the terms of the Creative Commons Attribution License