versão impressa ISSN 0012-7353
Dyna rev.fac.nac.minas v.74 n.152 Medellín maio/ago. 2007
ESTUDIO DEL MECANISMO DE FALLA DE TERRAPLENES DEBIDO A LA INFILTRACIÓN DE AGUAS LLUVIAS MEDIANTE EL MONITOREO DE PRESIONES DE POROS Y CONTENIDOS DE AGUA
STUDY OF FAILURE MECHANISM IN EMBANKMENTS INDUCED BY RAINFALL INFILTRATION BY MONITORING PORE WATER PRESSURES AND WATER CONTENTS
Lecturer, Department of Civil Engineering, University of Antioquia, email@example.com
Associate Professor, Department of Civil Engineering, University of Tokyo, firstname.lastname@example.org
Recibido para revisar 27 de Julio de 2006, Aceptado 14 de Noviembre de 2006, Version final 24 de Enero de 2007
RESUMEN: El presente artículo muestra experimentos realizados utilizando modelos a escala para estudiar el proceso de infiltración en terraplenes sometidos a aguas lluvias. Varios modelos a escala fueron construidos usando un suelo arenoso con alto contenido de finos; para aplicar la lluvia artificial y observar el proceso de infiltración del agua se utilizó un tubo de irrigación. Para monitorear los cambios en succión ocasionados por los ciclos de humedecimiento y secado se instalaron dentro del suelo varios sensores de presión de poros, contenido de agua y de desplazamiento en diferentes puntos. El cambio de la presión de poros en el tiempo, el contenido de agua y las relaciones entre las mediciones de presión de poros y desplazamientos del suelo son presentados. Este estudio muestra que el movimiento del suelo en un talud está directamente relacionado con el contenido de agua del suelo y las presiones de poros existentes en él, sugiriendo que por medio del monitoreo de estos dos parámetros es posible predecir fallas locales inducidas por infiltración de aguas lluvias en los taludes.
ABSTRACT: This paper presents experiments using scale models to study the infiltration process on embankments subjected to rainfall infiltration. Various model embankments were built using a silty sand soil; an irrigation pipe was used to applied artificial rainfall in order to observe the effect of the water infiltration. Pore water pressure, water content and displacements transducers were installed within the scale models at various locations to monitor the changes in suction caused during cycles of wetting and drying processes. Pore water pressure histories, water content histories and relations between measurements of pore water pressures and displacements are presented. This study showed that slope movements are directly related to the soil water content and pore water pressures within the slope, suggesting that slope failure caused by rainfall infiltration could be predicted by monitoring these parameters.
KEY WORDS: Embankment, unsaturated soils, rainfall effect, rainfall infiltration.
PALABRAS CLAVE: Terraplén, suelos no saturados, efecto lluvia, infiltración de aguas lluvias.
Slope failure may be triggered by many natural conditions: earthquakes, rainfalls, volcanic eruptions, snow melting, human activities, etc. Among natural hazards, landslides occur in virtually every country in the world. Globally, they cause approximately 1000 deaths a year with property damage of about US 4 billion (Orense 2003). Colombia as a tropical country has two rainy seasons during the year (March to May and September to November); during this time heavy rainfall causes considerable damage to highways, serious threats to settlements, transport infrastructure and tourism. Although, newly constructed embankments are adopted with various soil improvement techniques such as geo-reinforcement and internal drainage facilities, old existing embankments are having poor drainage conditions that lead to instability of the structure with water infiltration. Considering the cost of improvement of all existing embankments, it is worth to understand the stability and the behavior of the embankments during and after rainfall infiltration in order to minimize the damage to the infrastructure and the human casualties caused by the failure of embankments.
To understand how slope failures result from rainfall infiltrations is necessary to study the unsaturated soils. Many times, slope failures occur when the soil is not completely saturated, in such a case, suction (negative pore water pressure) within the soil becomes an important parameter for analyzing the behavior of the soils. Nevertheless, this behavior cannot be explained by the classical soil mechanism, which primary emphasis has been the behavior of dried or saturated soils.
Variation in suction and an increase in pore water pressures reduce the shear strength of soils causing failures; Yoshida et al (1991a, 1991b) and Gallage et al (2005) studied these effects of saturation on the shear strength of soils taken at the landslides sites due to heavy rainfall in recent years. Modeling of scale embankments and monitoring of water contents and negative and positive pore water pressure within the soil, allow us to understand and to correlate the response of the soils due to the rainfall infiltration in the field with the variation of the strength parameter obtained by laboratory tests.
This paper presents the results of monitored pore-water pressure, monitored water content and lateral displacements at several locations in model slopes during and after an artificial rainfall. Then, the pore-water pressure and water content are plotted against the time to study the drying and wetting processes within the model tests. Infiltration process was explained by the recorded pore water pressures and their distribution. The pore water pressures recorded by two sensors were plotted against lateral displacement in order to show the movement of the soil caused by the water infiltration and the reduction in soil suction. Finally, the contour failures obtained at the final of the test were shown, as well as the pictures of the failure process during the rainfall application.
2. TEST MATERIALS, APPARATUS AND PROCEDURES
2.1 Test materials
In the model tests, two soils were used to construct the embankments. Physical properties of the tested materials are shown in table 1. Figure 1 shows the grain size distribution of the mentioned soils.
2.2 Embankment Model and measurement systems
Figure 2 shows the schematic diagram of the soil box and the location of the transducers used for the model embankment No. 1. The major components of the system are: soil box, pore pressure sensors, ceramic cups, water content sensors and rainfall system.
The soil box used in the model test is 220 cm long, 80 cm wide and 100 cm high. The walls of the soil box are made of steel plates, except for the front side which is made of transparent acrylic in order to facilitate the observation of the process. Pore pressure meters and soil moisture content meters were installed within the model embankment. A perforated wall with wired mesh was used at the toe of the embankment in order to allow the free water drainage of the infiltrated water.
Pore pressure transducers were used to monitor the positive and negative pore water pressure caused by the infiltration of the water within the slope model. Porous ceramic round bottom straight cups were attached to the pore water transducers in order to measure negative pore water pressures. The porous ceramic used is 1.27 cm diameter, 6.35 cm in length and 0.32 cm thick. It has an air entry value of 100 kPa. Soil moisture transducers were used to monitor the volumetric water content. Sensors are shown schematically in figure 3. The output signals from the electronic transducers were sent to the A/D converter and finally to the computer, where data sampling was recorded every two seconds for the wetting process and every 5 minutes for the drying process.
2.2.2 Model test preparation
Soil preparation: The soil used to make the slope, was dried in an oven for 24 hours. After drying the soil, it was necessary to crush it using a tamping rod in order to achieve a natural grain size distribution. The grain size distribution of the soil used did not change with this procedure. Once the soil was crushed, water was added to it to reach required initial water content in between 12% and 18% to do the compaction process easier.
Saturation of ceramic cups: The ceramic cups attached to the pore pressure transducers were used to measure suction within the soil. In order to saturate the ceramic cups, they were immersed in a cylinder filled with water and a vacuum was applied to the cylinder. After this process, the ceramic cups were attached to the pore pressure transducers within the water-filled cylinder.
Placement and compaction of the soil: The model slope was constructed in the central portion of the soil box, and was prepared by the moist placement method or tamping. Next, the moist soil was placed in a series of horizontal layers. Each layer was tamped equally using a tamping rod to a thickness of 5 cm. This procedure was repeated until the full height of the model slope was achieved.
Placement of the sensors: During the soil placement, pore pressure transducers and water content transducers were placed at specific locations within the slope. Before placement of the pore water pressure sensors, soil was disturbed and the sensor was place on it in order to achieve good contact between the soil and the ceramic cup, next, a new layer of soil was placed above the sensor. The procedure for placing the moisture content sensor was different; after the pore water pressure sensor was fixed and a new soil layer was placed and compacted, a portion of the soil was removed and the sensor was inserted laterally into the compacted soil.
Rainfall simulation: After preparation of the slope, a spray irrigation pipe was used to simulate artificial rainfall. This pipe produces a fine side spray that simulates constant rainfall. Rainfall intensities of between 40 and 50 mm/hr were simulated using this system. Intensities of between 80 and 100 mm/hr were achieved using two pipes. The first rainfall was applied during the second day of the tests. After the first rainfall the model embankment was subjected to drying process without rainfall, because the model test was conducted outside the laboratory it was covered with a plastic sheet to avoid the effect of natural rainfall. The models were subjected to a second rainfall in the fourth day. Intensities, durations of the rainfalls and duration of the tests are shown in Table 2. Four burettes were used to measure rainfall intensity, two located at the bottom of the embankment and two at the top.
3. EXPERIMENTAL RESULTS AND DISCUSSION
In order to observe the general pattern of the rainfall infiltration, a series of slope model tests were performed. Artificial rainfall was applied to the model embankments using an irrigation pipe. Pore water pressure transducers to monitor the negative and the positive pore water pressures and water content transducers to measure volumetric water contents, were installed within the model slope at various locations. To measure the displacement of the soil due to the rainfall infiltration, displacement transducers were used in some model tests. All models responded similarly to the infiltration process.
3.1 Pore water pressure history
Figure 4 shows the time histories of monitored pore water pressure for model test No. 02 (see figure 2 for the location of the transducers). This graph shows that when the first rainfall was applied to the model the negative pore water pressures (suction) started to decrease rapidly. Next, when this rainfall was stopped (drying process), the recorded negative pore water pressures increased, especially in the sensors at the top (sensors P1 to P5). This increment in negative pore water pressure within the soil is strongly related with the depth of the slope; sensors within the top of the model presented higher suctions than those sensors located at the bottom. This graph also shows that recovering in suctions is very slow, suggesting that water was retained during a period of time within the soil.
3.2 Pore water pressure distribution
Monitored pore water pressure distributions for model test No. 2 are shown in figure 5. Four different sketches are shown. At the beginning of the test the model showed uniform pore water pressure in between -5 and -6 kPa (see figure 5.a). Figure 5.b shows the pore water pressure distribution after 18 hours of applying the first rainfall (after 40 hours); suction in the soil reduced to levels in between -1 and -2 kPa and close to zero at the toe of the model. Figure 5.c shows the state of the model when the rainfall was stopped, (drying process, after 68 hours), suction recovered specially at the top of the model, where the soil reached values similar to those at the beginning of the test, but, at the bottom of the model, lower values of suction were recorded, it can be explained by the accumulation of the water on the bottom of the soil box. Finally, pore water pressure distribution during the second rainfall is shown in figure 5.d (after 71 hours); infiltrated water began to accumulate at the bottom of the model, showing the pore water pressures close to zero after 2 hours of the second rainfall. In all the model tests, water table started to build up from the bottom to the top triggering local retrogressive failure from the bottom of the model.
Generally, the patterns of the pore water pressure distribution are a good indicator of the propagation of the wetting front, the infiltrated water reached initially the sensors close to the surface and finally the sensors located at the bottom. Similar behavior was observed within the model using Inage sand.
3.3 Moisture content history
Figure 6 shows the histories of monitored water content within the slope. This graph shows that when rainfall 1 was applied (19 hours), the soil was saturated very fast and it remained with constant water content during the application of this rainfall. When rainfall 1 was stopped, water moved from the top to the bottom and lower water content at the top of the model was recorded (sensors M1 to M4). In contrast, sensors located at the bottom (M5 to M8) remained at the same water contents, then, water accumulated at the bottom of the slope. When rainfall 2 was applied to the model, sensors responded quickly showing saturation within all the locations, but after stopping this rainfall, a similar response of the sensors to that showed after rainfall 1 was observed; water was moving from the top and it accumulated at the bottom.
As it was found by the pore water pressure measurements, drying or drainage process is faster at the top than at the bottom locations, it could be because of the movement of water from the top to the bottom of the model and due to the evaporation which is higher in the soil close to the surface.
3.4 Horizontal displacement history
Figure 7 shows a picture of the location of the displacement transducers used in the model embankment No. 7. These devices measured the lateral displacement in the model due to the saturation of the soil.
Figure 8 shows the monitored pore water pressure histories of the sensors P3 and P8 and the monitored displacement histories of the transducers D01 and D02 in model test No. 7. Sensors P3 and P8 are the closest sensors to D01 and D02, respectively; the position of the sensor are shown in figure 2. Figure 8 shows that when rainfall 1 was applied, the negative pore water pressures decreased and the lateral displacements increased within the model test; these deformations of the model continue increasing even when the rainfall 1 was stopped; but, they tended to stabilize after some hours. When rainfall 2 was applied, displacement of the soil increased again and once the pore water pressure were positive the model started to fail. It suggests that displacements are strongly related to the growth of water content within the soil. This observation is consistent with the results of triaxial tests on unsaturated specimens, where the most critical parameter in failure initiation was the degree of saturation (Farooq 2002). Monitoring of the water contents within the soils can predict failure induced by rainfall infiltration. Figure 9 shows the final failure contours of model tests No.4 and No.7. This figure shows that the final contours have similar shape assuring good repeatability of the tests. The tests suggested that failure initiated when water content within the soil increased, especially at the toe of the slope where the soil reaches positive pore water pressures, in contrast, a major portion of the sliding mass may still be in an unsaturated condition. Positive pore water pressure at the toe contributes to the development of highly unstable area at the slope toe which influences on overall instability. This suggests that the effective drainage at the slope toe can prevent progressive sliding due to build up of water table. Tohari et al (2000), observed similar failure mechanism in artificial model slopes, explaining that the saturation process significantly reduced moisture shear strength of the soil, and the increase if water table within the slope decreased the effective stress of the soil, especially at the slope toe.
3.5 Failure mechanism
Model No. 7 was prepared to be tested at the same conditions of model No. 4. Figure 10 shows some photographs at various stages during the second rainfall. Water infiltrated within the model started to accumulate from the bottom of the slope. Water content and pore water pressure increase at this portion of the model; the effective stress decreased due to the increment in pore water pressure, until the soil located at the toe reached the failure line. Then, failure progressed due to the continuous saturation. Finally, after progressive failure at the toe, a sliding plane was formed, and the soil mass slipped. As it is showed by the pictures, due to the resulting instability, beginning from the toe of the slope, retrogressive failure occurred.
The tests suggested that failure initiated when water content within the soil increased, especially at the toe of the slope where the soil reaches positive pore water pressures, in contrast, a major portion of the sliding mass may still be in an unsaturated condition.
Soil displacements with the tested embankments are directly related to the soil water contents and pore water pressures within the slopes. The higher the water pressures, the higher the displacements within the soil. Local failure appears at the bottom of the embankments and progressed to the top triggering global failure in the model embankments. Prediction of local and global failure in slopes could be inferred by monitoring water contents and pore water pressures within the soil
5. REFERENCES [ Links ]